- whatsapp +51955515985
- support@ecuforcetruck.com
- 24/7 Customer Support
Menu
Shop
Account
Subtotal: $0.00
No products in the cart.
Circuit Description
Normally, switches, accelerators, and other components are connected to the engine control module (ECM) directly through individual wires. Multiplexing allows those same components to be hard wired to an original equipment manufacturer (OEM) vehicle electronic control unit (VECU) or transmission electronic control unit (ECU) in the cab. Then component values and states from components such as sensors, accelerators, and switches can be transmitted from the OEM VECU to the Cummins® ECM over the SAE J1939 data link.
Messages sent from OEM VECUs or transmission ECUs are received by the Cummins® ECM and used for controlling the engine. The Cummins® ECM and OEM VECU(s) must be configured properly, so that proper operation of the multiplexed components will occur.
Component Location
The SAE J1939 data link wiring and the SAE J1939 devices vary by OEM options.
Conditions for Running the Diagnostics
This diagnostic runs continuously when the keyswitch is in the ON position or when the engine is running.
Conditions for Setting the Fault Codes
The Engine Control Module (ECM) did not receive a message from a multiplexed device.
The Engine Control Module (ECM) detected an open or short circuit condition in the J1939 data link harness.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp immediately when the diagnostic runs and fails.
The multiplexed device will not operate.
Conditions for Clearing the Fault Code
To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
The fault code status displayed by INSITE™ electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
The Reset All Faults command in INSITE™ electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
When this fault code is active, some multiplexed devices can possibly not function as desired.
This fault can occur for the following reasons:
When the ECM is set up properly (components enabled and OEM VECU source addressed correctly) to receive information from an OEM VECU, but the OEM VECU is actually transmitting a message that says that component is not available for multiplexing. This can be caused when a multiplexed component is enabled in the ECM, but the OEM VECU source address of the VECU transmitting the component message is incorrect in the Cummins® ECM, or the OEM VECU is not set up to transmit the multiplexed component message.
This fault can also be caused by a damaged J1939 data link connection between the OEM VECU and Cummins® ECM, a damaged connection between the component and the OEM VECU, damaged OEM VECU or damaged Cummins® ECM. It can become necessary to contact the OEM for proper multiplexing configuration.
It is possible to use INSITE™ electronic service tool to monitor multiplexed components.
Reference the appropriate OEM wiring diagram when troubleshooting circuits that utilize wiring supplied by the OEM.
Possible Cause:
1) ECM calibration
Related
Categories Cumminz, DTC TRUCKS, Tags , 1-, 2018, 6339, 9, 96, Abnormal, CM2450, Code, Cummins, Fault, FMI, Fuel, Level, Newer, PID, Rate, SPN, Update, X124B, X15
Wiring Diagrams
Component Locators
- Freightliner ServiceLink 4.9.6
Freightliner$30.00
Rated 0 out of 5
- AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125
AGCO$120.00
Rated 0 out of 5
- Diesel Diagnostic Link 8.17 SP1 2023
Detroit$96.00
Rated 0 out of 5
- 10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT$110.00
Rated 0 out of 5
- Diamond Logic Builder DLB 2019 Database 2019
Navistar$50.00
Rated 0 out of 5
- Allison doc premium update 2023 v1 Diagnostic Software Download
Allison$96.00
Rated 0 out of 5
- Bendix Acom Pro 2022 v3 ( 1 PC ) BENDIX 2022 V3
Bendix$85.00
Rated 0 out of 5
- CLAAS WebTIC Offline [11.2021] Service Information – ENGLISH Language
CLAAS$100.00
Rated 0 out of 5
- Nexiq eTechnician 1.3.62 2020 etechnician software
NEXIQ$50.00
Rated 0 out of 5
Scania$30.00
Rated 0 out of 5
- Meritor Wabco Tool Box 12.9.1
Trucks software$35.00
Rated 0 out of 5
- Volvo Penta EPC 6 Offline VMware [12.2021] VMware
Trucks software$64.00
Rated 0 out of 5
- Cat Factory Password Generator 1.0 2019 WINDOWS 10
CAT$55.00
Rated 0 out of 5
NISSAN UD$100.00
Rated 0 out of 5
- International Truck ISIS – Oncommand Service Information Q4.2020 [04.2020]
Navistar$85.00
Rated 0 out of 5
- JPRO 2022 v3 ( 1 PC )
JPRO$94.00
Rated 0 out of 5
- DETROIT DDDL 8.14 SP3 – Detroit Diesel Diagnostic Link 8.14 SP3 2021 ( 1PC )
Detroit$73.00
Rated 0 out of 5
- 10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT$110.00
Rated 0 out of 5
- Bobcat Service Library [03.2019] Service, Operator, Maintenance, Bulletines, etc full update
Bobcat$110.00
Rated 0 out of 5
- AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125
AGCO$120.00
Rated 0 out of 5
Related products
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- PACCAR PX-9 CM2350 (2013-17) Fault Code:3634 PID: SPN:5484 FMI:4 Engine Fan Clutch 2 Control Circuit – Voltage Below Normal or Shorted to Low Source
DTC TRUCKS
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 319 SMS
BOBCAT$49.00
Rated 0 out of 5
- SERVICE MANUAL DETROIT DIESEL DDDL 7 U
DETROIT$20.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROTRON 106-110-115-120-135-150-165 MK3
DEUTZ$34.00
Rated 0 out of 5
- SERVICE MANUAL VOLVO D16 (2009)
TRUCK MANUALS$30.00
Rated 0 out of 5
- SERVICE MANUAL HINO FD.FE.FF.SG 2017
HINO$36.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 310 – 313 SMS
BOBCAT$45.00
Rated 0 out of 5
- SERVICE MANUAL DETROIT DIESEL DDEC III – IV Master 2000 Training
DETROIT$25.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 943 sms
BOBCAT$40.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 430 SMS
BOBCAT$52.00
Rated 0 out of 5
FUSO$30.00
Rated 0 out of 5